Not all fires are the same, and they are classified according to the type of fuel that is burning. If you use the wrong type of fire extinguisher on the wrong class of fire, you can, in fact, make matters worse. It is therefore very important to understand the four different fire classifications.

	Class A - Wood, paper, cloth, trash, plastics Solid combustible materials that are not metals. (Class A fires generally leave an Ash.)
	Class B - Flammable liquids: gasoline, oil, grease, acetone Any non-metal in a liquid state, on fire. This classification also includes flammable gases.   (Class B fires generally involve materials that Boil or Bubble.)
	Class C - Electrical: energized electrical equipment As long as it's "plugged in," it would be considered a class C fire.  (Class C fires generally deal with electrical Current.)
	Class D - Metals: potassium, sodium, aluminum, magnesium Unless you work in a laboratory or in an industry that uses these materials, it is unlikely you'll have to deal with a Class D fire. It takes special extinguishing agents (Metal-X, foam) to fight such a fire.       Most fire extinguishers will have a pictograph label telling you which classifications of fire the extinguisher is designed to fight. APW stands for "air-pressurized water." APWs are large, silver extinguishers that are filled about two-thirds of the way with ordinary tap water, then pressurized with normal air. In essence, an APW is just a giant squirt gun. APWs stand about 2 feet tall and weigh approximately 25 pounds when full. Water (APW) Extinguishers APWs are designed for Class A (wood, paper, cloth) fires only. Never use water to extinguish flammable liquid fires. Water is extremely ineffective at extinguishing this type of fire, and you may, in fact, spread the fire if you try to use water on it. Never use water to extinguish an electrical fire. Water is a good conductor, and there is some concern for electrocution if you were to use water to extinguish an electrical fire. Electrical equipment must be unplugged and/or de-energized before using a water extinguisher on it. APWs extinguish fire by taking away the "heat" element of the fire triangle. APWs will be found in older buildings, particularly in public hallways, as well as in Residence Halls. They will also be found in computer laboratories. It is important to remember, however, that computer equipment must be disconnected from its electrical source before using a water extinguisher on it.    Carbon Dioxide Extinguishers  Carbon Dioxide extinguishers are filled with non-flammable carbon dioxide gas under extreme pressure. You can recognize a CO2 extinguisher by its hard horn and lack of pressure gauge. The pressure in the cylinder is so great that when you use one of these extinguishers, bits of dry ice may shoot out the horn. CO2 cylinders are red and range in size from 5 lbs to 100 lbs or larger. In the larger sizes, the hard horn will be located on the end of a long, flexible hose. CO2s are designed for Class B and C (flammable liquid and electrical) fires only. Carbon Dioxide is a non-flammable gas that extinguishes fire by displacing oxygen, or taking away the oxygen element of the fire triangle. The carbon dioxide is also very cold as it comes out of the extinguisher, so it cools the fuel as well. CO2s may be ineffective at extinguishing Class A fires because they may not be able to displace enough oxygen to successfully put the fire out. Class A materials may also smolder and re-ignite. CO2s will frequently be found in laboratories, mechanical rooms, kitchens, and flammable liquid storage areas.     Dry Chemical Extinguishers Dry Chemical Extinguishers come in a variety of types. You may see them labeled: "DC" short for "dry chem" "ABC" indicating that they are designed to extinguish class A,B,and C fires, or "BC" indicating that they are designed to extinguish class B and C fires. At OSU, "ABC" fire extinguishers are filled with a fine yellow powder. The greatest portion of this powder is composed of monoammonium phosphate. Nitrogen is used to pressurize the extinguishers. ABC extinguishers are red and range in size from 5 lbs to 20 lbs on campus.   It is extremely important to identify which types of dry chemical extinguishers are located in your area. Read the labels and know their locations! You don't want to mistakenly use a "BC" extinguisher on a Class A fire, thinking that it was an "ABC" extinguisher. An "ABC" extinguisher will have a label like this, indicating that it may be used on class A, B and C fires. Dry chemical extinguishers put out fire by coating the fuel with a thin layer of dust, separating the fuel from the oxygen in the air. The powder also works to interrupt the chemical reaction of fire, so these extinguishers are extremely effective at putting out fire. These extinguishers will be found in a variety of locations. New buildings will have them located in public hallways. They may also be found in laboratories, mechanical rooms, break rooms, chemical storage areas, offices, university vehicles, etc. Dry chemical extinguishers with powder designed for Class B and C fires may be located in places such as commercial kitchens or areas with flammable liquids.   Fires can be very dangerous and you should always be certain that you will not endanger yourself or others when attempting to put out a fire. For this reason, when a fire is discovered: Assist any person in immediate danger to safety, if it can be accomplished without risk to yourself. Activate the building fire alarm system or notify the fire department by dialing 911 (or designating someone else to notify them for you). When you activate the building fire alarm system, it will automatically notify the fire department and get help on the way. It will also sound the building alarms to notify other occupants, and it will shut down the air handling units to prevent the spread of smoke throughout the building. Only after having done these two things, if the fire is small, you may attempt to use an extinguisher to put it out. However, before deciding to fight the fire, keep these rules in mind: Know what is burning. If you don't know what is burning, you don't know what type of extinguisher to use. Even if you have an ABC extinguisher, there may be something in the fire that is going to explode or produce highly toxic smoke. Chances are, you will know what's burning, or at least have a pretty good idea, but if you don't, let the fire department handle it. The fire is spreading rapidly beyond the spot where it started. The time to use an extinguisher is in the incipient, or beginning, stages of a fire. If the fire is already spreading quickly, it is best to simply evacuate the building, closing doors and windows behind you as you leave.   Do Not Fight the Fire If: You don't have adequate or appropriate equipment. If you don't have the correct type or large enough extinguisher, it is best not to try to fight the fire. You might inhale toxic smoke. If the fire is producing large amounts of smoke that you would have to breathe in order to fight it, it is best not to try. Any sort of combustion will produce some amount of carbon monoxide, but when synthetic materials such as the nylon in carpeting or foam padding in a sofa burn, they can produce highly toxic gases such as hydrogen cyanide, acrolein, and ammonia in addition to carbon monoxide. These gases can be fatal in very small amounts. Your instincts tell you not to. If you are uncomfortable with the situation for any reason, just let the fire department do their job. The final rule is to always position yourself with an exit or means of escape at your back before you attempt to use an extinguisher to put out a fire. In case the extinguisher malfunctions, or something unexpected happens, you need to be able to get out quickly, and you don't want to become trapped. Just remember always keep an exit at your back.   When using a fire extinguisher, remember PASS It's easy to remember how to use a fire extinguisher if you can remember the acronym PASS, which stands for Pull, Aim, Squeeze, and Sweep.